First version for OBP 60 Light

lib/obp60task/OBP60Hardware.h

@@ -1,6 +1,7 @@
     // General hardware definitions
     // CAN and RS485 bus pin definitions see obp60task.h
 
+#ifdef HARDWARE_V21
     // Direction pin for RS485 NMEA0183
     #define OBP_DIRECTION_PIN 18
     // I2C
@@ -73,5 +74,88 @@
     #define OBP_BACKLIGHT_LED 15    // GPIO port
     // Power Rail
     #define OBP_POWER_50 5          // 5.0V power rail
+#endif
 
+// Hardware configuration for OBP60 LIGHT
+
+#ifdef HARDWARE_LIGHT
+    // Direction pin for RS485 NMEA0183
+    #define OBP_DIRECTION_PIN 8
+    // I2C
+    #define I2C_SPEED 10000UL       // 10kHz clock speed on I2C bus
+    #define OBP_I2C_SDA 21
+    #define OBP_I2C_SCL 38
+    // DS1388 RTC
+    #define DS1388_I2C_ADDR 0x68    // Addr. 0x68
+    // BME280
+    #define BME280_I2C_ADDR 0x76    // Addr. 0x76 (0x77)
+    // BMP280
+    #define BMP280_I2C_ADDR 0x77    // Addr. 0x77 (0x76) Attention: Pull up resistor
+    // BMP085 / BMP180
+    #define BMP180_I2C_ADDR 0x77    // Addr. 0x77 (fix)
+    // SHT21 / HUT21
+    #define SHT21_I2C_ADDR 0x40     // Addr. 0x40 (fix)
+    // AS5600
+    #define AS5600_I2C_ADDR 0x36    // Addr. 0x36 (fix)
+    // INA219
+    #define SHUNT_VOLTAGE 0.075     // Shunt voltage in V by max. current (75mV)
+    #define INA219_I2C_ADDR1 0x40   // Addr. 0x41 (fix A0 = 5V, A1 = GND) for battery
+    #define INA219_I2C_ADDR2 0x41   // Addr. 0x44 (fix A0 = GND, A1 = 5V) for solar panels
+    #define INA219_I2C_ADDR3 0x45   // Addr. 0x45 (fix A0 = 5V, A1 = 5V) for generator
+    // INA226
+    #define INA226_I2C_ADDR1 0x41   // Addr. 0x41 (fix A0 = 5V, A1 = GND) for battery
+    #define INA226_I2C_ADDR2 0x44   // Addr. 0x44 (fix A0 = GND, A1 = 5V) for solar panels
+    #define INA226_I2C_ADDR3 0x45   // Addr. 0x45 (fix A0 = 5V, A1 = 5V) for generator
+    // Horter modules
+    #define PCF8574_I2C_ADDR1 0x20  // First digital out module
+    // FRAM (e.g. MB85RC256V)
+    #define FRAM_I2C_ADDR 0x50
+    // SPI (E-Ink display, Extern Bus)
+    #define OBP_SPI_CS 45
+    #define OBP_SPI_DC 46
+    #define OBP_SPI_RST 47
+    #define OBP_SPI_BUSY 48
+    #define OBP_SPI_CLK 12
+    #define OBP_SPI_DIN 11
+    #define SHOW_TIME 6000        // Show time in [ms] for logo and WiFi QR code
+    #define FULL_REFRESH_TIME 600 // Refresh cycle time in [s][600...3600] for full display update (very important healcy function)
+    // SPI SD-Card
+    #define SD_SPI_CS 10
+    #define SD_SPI_MOSI 40
+    #define SD_SPI_CLK 39
+    #define SD_SPI_MISO 13
+
+    // GPS (NEO-6M, NEO-M8N, ATGM336H)
+    #define OBP_GPS_RX 19
+    #define OBP_GPS_TX 20
+    // 1Wire (DS18B20)
+    #define OBP_1WIRE 17        // External 1Wire
+    // Buzzer
+    #define OBP_BUZZER 18
+    #define TONE1 1500          // 1500Hz
+    #define TONE2 2500          // 2500Hz
+    #define TONE3 3500          // 3500Hz
+    #define TONE4 4000          // 4000Hz
+    // Analog Input
+    #define OBP_ANALOG0 3       // Analog input for voltage power supply
+    #define MIN_VOLTAGE 10.0    // Min voltage for under voltage detection (then goto deep sleep)
+    #define POWER_FAIL_TIME 2   // in [ms] Accept min voltage until 2 x 1ms (for under voltage gaps by engine start)
+    // Buttons
+    #define UP 6                // Wheel up
+    #define DOWN 4              // Wheel down
+    #define CONF 5              // Wheel press
+    #define MENUE 2             // Button top
+    #define EXIT 1              // Button bottom
+
+    // Flash LED (1x WS2812B)
+    #define NUM_FLASH_LED 1         // Number of flash LED
+    #define OBP_FLASH_LED 10        // GPIO port
+    // Backlight LEDs (6x WS2812B)
+    #define NUM_BACKLIGHT_LED 6     // Number of Backlight LEDs
+    #define OBP_BACKLIGHT_LED 40    // GPIO port
+    // Power Rail
+    #define OBP_POWER_50 41         // Power LED
+    #define OBP_POWER_EPD 7         // ePaper power
+    #define OBP_POWER_SD 42         // SD card power
+#endif